Edatec HMI2120 basert på CM4

2.979,00 NOK4.939,00 NOK
(2.383,20 NOK ekskl. mva)

CM4 7″ or 10.1» Industrial Panel Computer.

DC strømforsyning for Edatec HMI og IPC - ED-PSU1202-EU-3.5PL

Strømforsyning i god kvalitet for for eksempel Edatec HMI og IPC.

Produktnummer: I/A Kategorier: ,

Beskrivelse






Appications

 

      
      

 

Documents Download

Specifications

System
CPUBroadcom BCM2711, quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz
VPU
H.265(HEVC), up to 4Kp60 decode
H.264, up to 1080p60 decode, 1080p30 encode)
GPUOpenGL ES 3.1 & Vulkan 1.0
MemoryOptions for 1GB, 2GB, 4GB, 8GB LPDDR4-3200 SDRAM
Storage
– Options for 8GB, 16GB, 32GB eMMC storage
– Micro SD card (user storage expansion)
– M.2 NVMe SSD (optional)

 

Software
Operating
System
– Raspberry Pi OS(Desktop) 32-bit
– Raspberry Pi OS(Lite) 32-bit
– Raspberry Pi OS(Desktop) 64-bit
– Raspberry Pi OS(Lite) 64-bit

 

Front I/O
CameraBuilt-in 800M front camera

 

Side I/O
Power
1 x DC IN, 2-Pin 3.5mm spacing phoenix terminals with screw holes.
It supports 9V~36V input, the signal is defined as VIN+/GND.
Audio
1 x Audio In/Stereo Out, 3.5mm audio jack connector. It can be used as MIC IN and LNE OUT.
– When a headphone is connected, the audio output switches to the headphone.
– When no headphone is connected, the audio output switches to the speaker.
RS485
2 x RS485, 6-Pin 3.5mm spacing phoenix terminals with IO isolator, equippes with electrostatic and surge protection, the single signal is defined as IGND/A/B.
RS232
2 x RS232, 6-Pin 3.5mm spacing phoenix terminals with IO isolator, equippes with electrostatic and surge protection, the single signal is defined as IGND/TX/RX.
1000M

Ethernet
1 x adaptive 10/100/1000M ethernet port, RJ45 connector. It can be used to access the network. PoE can be supported through expansion module.
100M
Ethernet
1 x adaptive 10/100M ethernet port, RJ45 connector. It can be used to access the network.
SD Card Slot1 x Micro-SD card slot, uses to install SD card for storing user data.
SIM Card Slot
1 x Nano SIM card slot, uses to install SIM card for getting 4G signal.
Micro USB1 x Micro USB port, supports to flash eMMC for the system.
HDMI1 x HDMI port, type A connector. It compatibles with HDMI2.1 standard and supports 4K 60Hz.
USB 2.02 x USB2.0 ports, type A connector, support up to 480Mbps.
Antenna
2 x SMA ports, use to connect 4G antenna and Wi-Fi/BT antenna.
Speaker1 x PA output, dual channel stereo audio output, built-in two 4Ω 3W speakers.

 

Buttons and Indicators
Reset1 x Reset button, which can reset the device.
PWR1 x red power indicator, uses to check the status of device power-on and power-off.
4G1 x green 4G indicator, uses to check the status of 4G singal.
ACT1 x green system indicator, uses to check the working status of device.
USER1 x green user indicator, user can customize a status according to actual application
COM1~COM44 x green UART indicators, uses to check the communication status of UART port

 

Expansion Performance
EEPROMSupports 4K byte storage and improves the ease of use of device.
Crypto
Authentication
It can be matched to realize the required upper layer application and improves the security of device.
RTC 
Ensure that the system clock is not affected by device power-off.
Note: A CR1220 battery is provided by default in China.
Buzzer
A tip or an abnormity can be configurated according to actual application, which realizes the alarm function.
Watch Dog
Realize the hardware Watch Dog based on the RTC alarm function to ensure the reliability of device

 

Expansion I/O
12V 1A
3 x DC OUT, 2-Pin 2.0mm spacing connector, support 12V 1A output.
These pins are defined as GND/12V, reserve to provide power supply for extended LCD.
40-pin GPIO
1 x GPIO, 2×20-Pin 2.54mm pitch header, uses to lead out the GPIO ports of CM4.
– These pins are defined as GPIO1~GPIO27/3V3/5V2/GND.
– Compatibles with expansion modules, and reserves to connect expansion accessories.
10-pin GPIO 
1 x GPIO Pin Header, 2×5-pin 2.54mm pitch header, uses to lead out the expansion GPIO ports. User can customize the function according to actual application, these pins are defined as 8xGPIO/3V3/GND.
HDMI
1 x FPC HDMI, 40-pin 0.5mm spacing FPC connector, which can be reserved to connect extended LCD, supports USB/I2C touch screen and backlight adjustment.
USB1 x USB 2.0, 5-pin 1.5mm spacing FPC connector, supports to expand the USB2.0 interface.
M.2 B
1 x M.2 B, M.2 B Key connector, supports to connect SSD. It compatibles with M.2 B 2230 and M.2 B 2242 SSD.

 

LCD
ED-HMI2120-070CED-HMI2120-101C
LCD Size7.0″ TFT10.1″ TFT
Resolution1024 x 6001280×800
Colors16.7MB16.7MB
Active Area154.21mm(H) x 85.92mm(V)216.576mm(H) x 135.36mm(V)
BacklightLEDLED
MTBF>30000h>30000h
Luminance400cd/m^2400cd/m^2
Contrast Ratio 800:11000:1
Response Time30ms30ms
Viewing Angle(CR≥10)85°(L)/85°(R)/85°(U)/85°(D)80°(L)/80°(R)/80°(U)/80°(D)

 

Touch Screen
TypeMulti-point Capacitive Touch Screen
Transmittance≥85%
Connection Method
COF
Controller Interface
I2C
Driver SupportLinux
Multi-touch10 points
Surface
Hardness
6H

 

Electrical Characteristics
Input Voltage9V ~ 36V DC
Maximum
Power

Consumption 

25W

 

Mechanical Characteristics
ED-HMI2120-070CED-HMI2120-101C
Dimensions188mm x 123mm x 43.5mm (WxDxH, antenna is not included.)263mm x 177mm x 42.5mm (WxDxH, antenna is not included.)
Weight1.1Kg1.5Kg
InstallationEmbeded installation, including front installation and rear installation.Embeded installation, including front installation and rear installation.

 

Wireless
Wi-Fi
(optional)
2.4GHz and 5GHz dual-band Wi-Fi with antenna.
– 2.4GHz Wi-Fi: Compatible with IEEE 802.11 b/g/n
– 5GHz Wi-Fi: Compatible with IEEE 802.11 a/n/ac
Bluetooth 
(optional)
Bluetooth 5.0 with antenna, compatible with 2402MHz ~ 2480MHz frequency
4G
(optional)
Connect with various 4G LTE modules through the Mini PCIe interface.

EC20-CN Module (China/India)
LTE FDD: B1/B3
LTE TDD: B38/B39/B40/B41
TDSCDMA: B34/B39
WCDMA: B1
CDMA 1x/EVDO: BC0
GSM: 900/1800MH
EC25-AFX Module (North America)
LTE-FDD:B2/B4/B5/B12/B13/B14/B66/B71
LTE-TDD
WCDMA: B2/B4/B5

GSM/EDGE

EC25-AUX Module (Latin America/Australia/New Zealand)

LTE-FDD: B1/B2/B3/B4/B5/B7/B8/B28
LTE-TDD: B40
WCDMA: B1/B2/B4/B5/B8

GSM/EDGE: B2/B3/B5/B8

EC25-EUX Module (Europe/Middle East/Africa/Thailand)
LTE-FDD: B1/B3/B7/B8/B20/B28A
LTE-TDD: B38/B40/B41
WCDMA: B1/B8
GSM/EDGE: B3/B8

 

Environmental & Regulatory
Operating Temperature
0°C ~ 50°C
Storage Temperature
-10°C ~ 60°C
Ambient Humidity20% ~ 90% (non-condensing)
Certifications
FCC
FCC 47 CFR Part 15 Subpart B
CE
EN IEC 62368-1/EN IEC 62311/EN IEC 61000-3-2/EN IEC 61000-3-3
EN 55032/EN 55035/
EN 301 489-1/EN 301 489-3/EN 301 489-17/EN 301 489-52
EN 301 328/EN 301 440/EN 301 511/EN 301 908-1/EN 301 908-2

System Block Diagram

Dimension Unit:mm

ED-HMI2120-101C

Oder Information

Tilleggsinformasjon

Vekt1600 g
Model

7 inch, No WiFi, 2GB RAM, 8GB Storage, 7 inch, WiFi, 2GB RAM, 8GB Storage, 10 inch, WiFi, 2GB RAM, 8GB Storage, 10 inch, 4G, WiFi, 8GB RAM, 32GB Storage

GTIN / EAN / UPC6976558371258
6976558371265
6976558371067
6976558370947
Manufacturer Product NumberED-HMI2120-070C-0208
ED-HMI2120-070C-1208
ED-HMI2120-101C-1208
ED-HMI2120-101C-18324EU
BrandEdatec
Country of OriginCN
HS Tariff Code8543709860

Omtaler

Det er ingen omtaler ennå.

Show only reviews in Norsk (0)

Bli den første til å omtale “Edatec HMI2120 basert på CM4”

Din e-postadresse vil ikke bli publisert. Obligatoriske felt er merket med *

Du liker kanskje også…