Non-Touch – HyperPixel 4″ Display

53,50
(42,80 excl. VAT)

A high-resolution, high-speed 4″ TFT display without touch for your Raspberry Pi.

HyperPixel is the perfect way to use your Pi without a bunch of cables or a bulky display. Design your own interface to control your projects or display your data, or turn your Pi into a tiny media centre.
If the product is on backorder: no guaranteed date of shipment.

Out of stock

Join the waitlist to be emailed when this product becomes available

SKU: 5121 Category: Compatibility: ,

Description

This is the newest version of HyperPixel WITHOUT touch. This new version of HyperPixel has a gorgeous IPS display, with wide viewing angles and the alternate I2C interface is broken out for advanced users. It’s available in touch and non-touch versions, depending on your preference. Note that the images of the displays on this page have not been Photoshopped. That’s the Raspbian desktop with our HyperPixel wallpaper on!

Features

  • High-speed DPI interface
  • 4.0″ IPS (wide viewing angle, 160°) display (86.4×51.8mm)
  • 800×480 pixels (~235 PPI)
  • 18-bit colour (262,144 colours)
  • 60 FPS frame rate
  • Contrast ratio: 500:1
  • 40-pin female header included to boost height for Pi B+, 2, 3, 3B+
  • Standoffs included to securely attach to your Pi
  • Compatible with Raspberry Pi 4, 3B+, 3, 2, B+, A+, Zero, and Zero W
  • One-line installer

HyperPixel uses a high-speed DPI interface, allowing it to shift 5x more pixel data than the usual SPI interface that these small Pi displays use. It has a 60 FPS frame rate and a resolution of approximately 235 pixels per inch (800×480) on its 4.0″ display. The display can show 18-bits of colour (262,144 colours). Everything comes fully-assembled, and there’s no soldering required! The display is securely stuck down to the HyperPixel 4.0 PCB and connected via a neat little flush-mounting FPC cable. Just pop HyperPixel 4.0 on your Pi and run our installer to get everything set up! Please note: when installing HyperPixel 4.0 onto your Pi make sure not to press down on the screen surface! Hold the board by its edges and wiggle it to mate with the extended header (or GPIO header). It’ll work with any 40-pin version of the Pi, including Pi Zero and Pi Zero W. If you’re using it with a larger Pi like the B+, 2, or 3, 3B+, then use the extra 40-pin header that’s included to boost it up to the required height. If you’re using a Zero or Zero W then just pop it straight onto the GPIO. The included standoff kit allows you to mount your HyperPixel 4.0 safely and securely to your Pi. Just screw them into the posts on the underside of the HyperPixel 4.0 PCB and then secure with screws through the mounting holes on your Pi.

Software

There is a one-line-installer to configure your Pi properly for HyperPixel 4.0 and to enable the touch screen on the touch version. Note that you’ll need another display, keyboard, and mouse to install the software, or you could do it remotely over SSH if you follow our guide on how to set your Pi up headlessly. Open a terminal, and type curl https://get.pimoroni.com/hyperpixel4 | bash to run the one-line installer and set your HyperPixel 4.0 up. Find the GitHub repository here: https://github.com/pimoroni/hyperpixel4 Software does not support Raspbian Wheezy.

Notes

Dimensions: 58.5x97x12mm (WxHxD, depth includes header and display).

Additional information

Weight104 g
GTIN / EAN / UPC0606034877832
Manufacturer Product Number
BrandPimoroni
Country of OriginGB
HS Tariff Code8528521000

Reviews

There are no reviews yet.

Show only reviews in English (0)

Be the first to review “Non-Touch – HyperPixel 4″ Display”

Your email address will not be published. Required fields are marked *