Kuvaus
ED-HMI2020-101C
◆ Features
Rasberry Pi CM4-based 10.1″ Industrial Tablet PC
- 10.1″ WSVGA TFT, 1280×800 resolution, multi-point capacitive touchscreen
- Broadcom BCM2711 4-core Cortex-A72 64-bit processor
- Up to 8GB of LPDDR4 RAM and 32GB of eMMC
- LAN port rate supports up to 1Gbps
- 2.4GHz & 5GHz Wi-Fi and Bluetooth wireless method
- Support micro-SD Card, integrated RTC, EEPROM and encryption chip
- 9V~28V wide voltage power input with over-current, over-voltage, reverse connection and surge protection
- High quality metal case, support embedded installation
◆ Documents Download
Datasheet Download
Application Guide Download
User Manual Download
◆ Specifications
| System | |
| CPU | Broadcom BCM2711, quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz |
| VPU | H.265(HEVC), up to 4Kp60 decode H.264, up to 1080p60 decode, 1080p30 encode) |
| GPU | OpenGL ES 3.1 & Vulkan 1.0 |
| Memory | Options for 1GB, 2GB, 4GB, 8GB LPDDR4-3200 SDRAM |
| Storage | – Options for 8GB, 16GB, 32GB eMMC storage – Micro SD card (user storage expansion) |
Software | |
Operating System | – Raspberry Pi OS(Desktop) 32-bit – Raspberry Pi OS(Lite) 32-bit – Raspberry Pi OS(Desktop) 64-bit – Raspberry Pi OS(Lite) 64-bit |
| Front I/O | |
| Camera | Built-in 800M front camera |
Side I/O | |
| Power | 1 x DC IN, DC Jack connector, supports 9V~28V input. |
| Audio | 1 x Audio In/Stereo Out, 3.5mm audio jack connector. It can be used as MIC IN and LNE OUT. – When a headphone is connected, the audio output switches to the headphone. – When no headphone is connected, the audio output switches to the speaker |
1000M Ethernet | 1 x adaptive 10/100/1000M ethernet port, RJ45 connector. It can be used to access the network. PoE can be supported through expansion module |
| SD Card Slot | 1 x Micro-SD card slot, uses to install SD card for storing user data. |
| HDMI | 1 x HDMI port, type A connector. It compatibles with HDMI2.1 standard and supports 4K 60Hz. |
| USB 2.0 | 2 x USB2.0 ports, type A connector, support up to 480Mbps. |
| Antenna | 1 x SMA port, uses to connect Wi-Fi/BT antenna. |
| Speaker | 1 x PA output, dual channel stereo audio output, built-in two 4Ω 5W speakers. |
| Buttons and Indicators | |
| Reset | 1 x Reset button, which can reset the device. |
| Rpiboot | 1 x Rpiboot button, uses to flash eMMC for the system. |
| PWR | 1 x red power indicator, uses to check the status of device power-on and power-off. |
| ACT | 1 x green system indicator, uses to check the working status of device. |
| Expansion Performance | |
| EEPROM | Supports 4K byte storage and improves the ease of use of device. |
Crypto Authentication | It can be matched to realize the required upper layer application and improves the security of device. |
| RTC | Ensure that the system clock is not affected by device power-off. Note: A CR1220 battery is provided by default in China. |
| Buzzer | A tip or an abnormity can be configurated according to actual application, which realizes the alarm function. |
| Expansion I/O | |
| 12V 1A | 1 x DC OUT, 2-Pin 2.0mm spacing connector, support 12V 1A output. These pins are defined as GND/12V, reserve to provide power supply for extended LCD. |
| 40-pin GPIO | 1 x GPIO, 2×20-Pin 2.54mm pitch header, uses to lead out the GPIO ports of CM4. – These pins are defined as GPIO1~GPIO27/3V3/5V2/GND. – Compatibles with expansion modules, and reserves to connect expansion accessories. |
| HDMI | 1 x FPC HDMI, 40-pin 0.5mm spacing FPC connector, which can be reserved to connect extended LCD, supports USB/I2C touch screen and backlight adjustment. |
| USB | 1 x USB 2.0, 5-pin 1.27mm spacing FPC connector, supports to expand the USB2.0 interface. |
| LCD | |
| LCD Size | 10.1″ WSVGA TFT |
| Resolution | 1280×800 |
| Colors | 16.7MB |
| Active Area | 135.36mm(H) x 216.576mm(V) |
| Backlight | LED |
| MTBF | >30000h |
| Pixel Pitch | 0.169mm x 0.169mm |
| Luminance | 350cd/m^2 |
| Contrast Ratio | 1000:1 |
| Response Time | 30ms |
Viewing Angle (H/V) | 80°/80° |
| Touch Screen | |
| Type | Multi-point Capacitive Touch Screen |
| Transmittance | ≥85％ |
Connection Method | COF |
Controller Interface | I2C |
| Driver Support | Linux |
| Multi-touch | 10 points |
Surface Hardness | 6H |
| Electrical Characteristics | |
| Input Voltage | 9V ~ 28V DC |
Maximum Power Consumption | 20W |
Mechanical Characteristics | |
| Dimensions | 263mm x 177mm x 40mm (WxDxH, antenna is not included.) |
| Weight | 1.1Kg |
| Installation | Embeded installation, including front installation and rear installation. |
Wireless | |
| Wi-Fi (optional) | 2.4GHz and 5GHz dual-band Wi-Fi with antenna. – 2.4GHz Wi-Fi: Compatible with IEEE 802.11 b/g/n – 5GHz Wi-Fi: Compatible with IEEE 802.11 a/n/ac |
| Bluetooth (optional) | Bluetooth 5.0 with antenna, compatible with 2402MHz ~ 2480MHz frequency. |
| Environmental & Regulatory | |
Operating Temperature | 0°C ~ 50°C |
Storage Temperature | -10°C ~ 60°C |
Ambient Humidity | 20% ~ 90%(non-condensing) |
| Certifications | FCC FCC 47 CFR Part 15 Subpart B CE EN IEC 62368-1/EN IEC 62311/EN IEC 61000-3-2/EN IEC 61000-3-3 EN 55032/EN 55035/ EN 301 489-1/EN 301 489-3/EN 301 489-17/EN 301 489-52 EN 301 328/EN 301 440/EN 301 511/EN 301 908-1/EN 301 908-2 |
◆ System Block Diagram
Arviot
Tuotearvioita ei vielä ole.